Professional Tool Reviews for Pros

Having already covered battery charging tips, we also wanted to cover lithium-ion battery maintenance tips. Lithium-ion batteries are expensive. You want to do all you can to extend the life of the fuel that powers your cordless tools. Of the top 5 killers, we have the most control over heat, but having good charging habits also helps considerably. Combined, all these tips should help add life to your battery packs.

Heat is the number one killer of battery performance. Most heat is generated by tool use and charging, but we can do a few things to minimize it.

Most chargers have an auto shut-off to stop the charging process when it reaches full. If you pull the battery off right at the end of the cycle, there will be some leftover heat. Even just sitting on a plugged-in charger generates a little bit of additional heat. Give it the benefit of cooling down for just a couple of minutes before putting it back under load.

Temperatures in the bed of your truck and inside your truck can skyrocket compared to the ambient temperature of the air. Storing your batteries there will have temperatures at over 100 degrees before you even turn the tool on. While not as extreme as being inside a vehicle, simply sitting in the sunshine will elevate the temperature as well. Likewise, if you’re taking even a short break from using the tool, set it in the shade until it’s needed again.

You’ll feel the temperature rising on the tool as it gets to the auto shut off point. Help maintain productivity by giving the tool frequent breaks in aggressive applications like demo work and concrete drilling.

Where I live, you start sweating as soon as you step foot in the garage. Opening the garage door helps some, but it’s not as nice as being in the air-conditioned house. Find a place to store and charge those batteries inside if your spouse lets you.

Batteries need to be not too hot, but also not too cold to perform at their best. When the temperatures drop, here are a few maintenance tips to warm them up some.

I know you’re running the heat in your truck on the way to the job site. Bring the batteries you’ll be using inside and point a vent near them. Allowing them to warm up on the way will help them deliver additional power and run time.

Exactly the opposite of what you do in high temperatures, but setting the battery and charger where it gets direct sunlight will raise the temperature more than sitting in the shade.

If you’re doing outdoor work on a heated building, go ahead and put your batteries and charger inside. It’s a little more inconvenient, but you’ll be switching batteries less often. When you’re done for the day, go ahead and bring them inside the house instead of making them spend the night in a cold shed or garage.

Sadly, there’s not a whole lot that you can do about vibration. The majority of the vibration that a battery experiences come from the tool and application itself. Still, there are a couple of common sense things to help.

The battery packs we use are more than just AA battery cells packed together. It’s a more complicated chemistry and housing. It also includes electronic communication components. Treat them nicely.

Secured in the toolbox? Sure. Running around loose in the bed? Absolutely not! Every time you turn a corner, accelerate, or stop, those batteries can slam into the side and generate a lot of force. For a better idea of what that looks like, go to YouTube and search for “Football Concussion Hits”.

Here’s another area that is hard to control. We all know that water and electricity are like daughters and dating, so be cautious of what you can do to prevent it.

Give them some clearance around water spigots, coolers, and 48 ounce Styrofoam cups of sweet tea. The housing is designed to draw moisture away from the cells, but once the damage is done, it’s done.

Sometimes you have to work in the rain. Just keep your spare batteries out of it. Keep them in your toolbox or under protective cover.

Our last Lithium-ion battery maintenance tip has to do with over-discharging. We have the most control over our charging habits. While charge and discharge create heat, there is also an optimum state for batteries to be in for both use and storage.

Charge your batteries before they completely run down to nothing. Even though you may still have 15%–25%  remaining when you hit one bar, you’ll significantly extend the lifespan of it by swapping it out sooner.

You also want to beware fo continuously running tools once they indicate the battery needs charging. Most drills will sit for a spell and then give you one more go. Resist the urge to use them in this way. Most modern battery packs have built-in protection against over-discharging. Still, you don’t want to push things by continuously pulling that trigger when the pack has told you to put it on the charger.

There’s a reason that manufacturers ship battier at a half-charged state: it’s their happy place. The battery chemistry is the most stable at half charge. Incidentally, they tend to perform at their highest potential at half charge as well. If you know you’re storing your batteries for more than a couple of days, go ahead and get them to a half-charged state. Even when you’re just storing them for the night or weekend, keep them at a partial charge when you’re done for the day. It’s perfectly okay to partially charge them to bring them up to half charge without limiting the life of the battery.

This doesn’t only let the temperature come down, it allows the chemistry to stabilize. By allowing both to happen, you’ll increase the run time on a single charge.

DCS spends most of his time watching Mythbusters, trying to figure out what the labels that they blur out say, so that he can recreate the explosions. His hobbies include impersonating Chuck Norris doing an impersonation of Sean Connery and fly fishing. David does his own stunts.

Changing Wheel Bearings Is Messy But Not Too Difficult Easy To Do On Your Own As I pulled my boat out of the garage and began to head down the road, it was immediately obvious something wasn’t right. The presence of a rhythmic thudding but no flat tire meant I had a bearing issue. My […]

Reading a Tape Measure Can Be Easy If You Know What to Look For Learning how to read a tape measure is one of the first things any Pro or DIYer has to learn. If the old adage “measure twice, cut once” is true, you’ll never get to the cut if you don’t know what […]

Rising Prices And Competition Are Pushing Families Out Of The Housing Market For the 4+ decades that I’ve been alive, the American Dream has always included home ownership. For many people, it’s more of an expectation than a dream. For those saving and working to get into their first home, that dream is beginning to […]

Construction Giant Caterpillar Sets Sights on the Dallas-Fort Worth Area Caterpillar, one of the largest manufacturers of heavy construction and mining equipment, released a statement that it plans to move its global headquarters from Deerfield, Illinois to Irving, Texas. It joins the likes of Tesla, Google, Samsung, Oracle, Hewlett Packard, Charles Schwab, and over 125 […]

I’ve discovered DeWalt tstack tool boxes are interchangeable with Craftsman and Stanley. Are there other 20 volt batteries or tool brands that are interchangeable with DeWalt?

i could be missing something but if you keep your batteries only half or partially discharged overnight or for the weekend, what’s the scenario when you head to work and go to use them? They won’t power for as long on the job which then becomes one big nuisance having to swap over midway. BTW i use an 18V Li-ion 6.0Ah battery in my vacuum cleaner, and before doing some research I always fully charged my batteries back up after use. Clearly this was wrong!! And another thing – when you have a backpack vacuum on, how can you know…  Read more »

Lol keeping them at half power defeats the purpose. That’s retarded

As an Amazon Associate, we may earn income when you click on an Amazon link. Thanks for helping us do what we love.

See our Privacy Policy and Terms & Conditions.

Pro Tool Reviews is a successful online publication that has been providing tool reviews and industry news since 2008. In today’s world of Internet news and online content, we found that more and more professionals researched a large majority of their major power tool purchases online. That piqued our interest.

There’s one key thing to note about Pro Tool Reviews: We’re all about the professional tool user and tradesman!

Copyright ©2008-2022 Pro Tool Reviews, LLC. All rights reserved.

Professional Tool Reviews for Pros